Jump to content
  • Travis

    By Travis

    Travis

    By Travis •

    Tips And Tricks

    There was a great idea posted in this thread about making a list of tips and tricks for scrollers. Having them in one place would be a great resource for new scrollers, and a fun place for seasoned scrollers to find new ideas.

     

    So post your favorite tips here and I'll add it to the list. Please keep the tips short and sweet so it's easy to read and add to the list.

     

    Let the sharing begin! :thumbs:

     

     

    ===================================================

      On 4/7/2015 at 3:11 PM, jerry1939 said:

    I am a "bottom feeder." After drilling a few holes, I take an awl and enlarge the bottom of the holes. This creates a funnel shape to put the blade in. On a large piece, if you have trouble seeing the hole, lay a CD on the saw table. It reflects A LOT of light up.

    Expand  
      On 4/7/2015 at 4:01 PM, Multifasited said:

    Take a pencil #2 rotate in hole makes it very visible.

    Expand  
      On 4/7/2015 at 4:42 PM, amazingkevin said:

    If you have a small grinder ,taper your blades like an arrow .

    Expand  
      On 4/8/2015 at 12:04 AM, edward said:

    I keep a push pin by the saw. Push it through the pilot hole and it works for me.

    Expand  
      On 1/7/2016 at 1:40 AM, orangeman said:

    1. small engineer's square for getting the 90 degree angle which is critical for puzzles

    2. packaging tape for blade lubrication.

    3. paste wax for the table

    4. band aids for those inevitable nicks on the fingers.

    5. Magnifying light.

    6. Good quality blades

    7. Dust mask or central vac system with good pick-up.

    8. Adjustable height chair with back support (drafting stool)

    9. Subscription to "ScrollSaw Workshop and crafts"

    10 3M sanding wheels (for use with drill, drill press, or lathe)

    11 3M "77" adhesive spray for permanent bond or Elmer's spray adhesive for temporary bond.

    Expand  
      On 1/7/2016 at 1:50 AM, jerry1939 said:

    [For Squaring The Blade] - I cut into a scrap. Stop the saw, spin the wood around to the back of the blade. If the blade goes into the cut, you're good. Low tech, but accurate.

    Expand  
      On 1/7/2016 at 2:32 AM, rjR said:

    For projects due to be repeated; I use a thin stable materiel (hardboard-- plastic etc.) and cut the template to re-use along with the original cuts!

     

    I also use an additional blade lube of old WHITE preferred candles ran right into the blade-- even between cuts. I have fantastic blade life.

    Expand  
      On 1/7/2016 at 3:43 AM, Sparkey said:

    I like having an air compressor with spray nozzle to blow all of the dust off my work when its finished.

     

    I always spray a clear coat over fretwork before I frame it to keep any stray sawdust off the inside of the plexiglass.

    Expand  
      On 1/7/2016 at 2:39 PM, jamminjack said:

    [Replacement Dust Blower] - I went and purchased an aquarium air pump and hooked it to the saw. Very powerful, and no more problems with saw dust on the project.

    Expand  
      On 1/7/2016 at 10:18 PM, Doug said:

    Use a sacrificial board under your piece with the pattern when drilling holes to avoid push out and after drilling sand the back with 220 grit so the surface on the saw table is smooth

    Expand  
      On 1/7/2016 at 10:39 PM, jerry1939 said:

    For really intricate cutting (especially 1/8"), I usually put a sacrifice luan ply above and below the piece. Saw all 3 pieces the same size and wrap with blue tape. Often put a dab of glue in the 4 corners also.

    Expand  
      On 4/9/2016 at 2:13 PM, Old Joe said:

    I keep a very small, cheap, shop vac next to my saw and use it constantly. I have also installed a ceiling mounted dust collector. Just blowing off the dust with the compressor is spreading it around the shop and it will end up in your finely sanded, oiled finish, not to mention your nose and lungs.

    Expand  
      On 4/9/2016 at 3:03 PM, Dan said:

    I have a cardboard box that I place over items I have applied a finish to. It protects the finish from any dust I happen to blow around while working on other projects.

    Expand  
      On 4/10/2016 at 2:28 PM, Jim Finn said:

    I have an $8 hair dryer blowing the dust off of my work as I saw.

    Expand  
      On 4/10/2016 at 2:28 PM, Jim Finn said:

    To use more of your blade teeth you can cut off the bottom 3/4" of a dulled blade reinstall, and you will then be using the unused teeth. Not sure all saws will accommodate the shorter blade but all mine will.

    Expand  
    Go to articles

    User Feedback

    Recommended Comments



    LarryEA
      On 1/16/2016 at 8:32 PM, Scrappile said:

    For bottom feeding detailed picture scrolling I use a hemostat to help feed the #3/0 blade into the tiny #65 hole and to pull it through from the top.

     

    My hemostats become magnetized often.  I put heat shrink tubing over the jaws to prevent the magnetism from grabbing the blade where I did want to grab it.  Worked great.

    and I use needle nose pliars

    Link to comment
    Share on other sites
    CharleyL

    For bottom feeding I use a 3" dia wide angle round mirror (domed style) intended to be glued to the side flat mirror of a truck to increase the driver's field of view. When laid on the saw table it magnifies the blade and holes making it easier to get the blade into the hole.

     

    Charley. 

    Link to comment
    Share on other sites
    Malcolm161
      On 1/7/2016 at 3:43 AM, Sparkey said:

    I like having an air compressor with spray nozzle to blow all of the dust off my work when its finished.

    I always spray a clear coat over fretwork before I frame it to keep any stray sawdust off the inside of the plexiglass.

     

    I thought about that Sparkey, but came down to the cans of compressed air that are available, which will do me for the time.  If the production line gets going, it may be a different matter, but start small and then progress is my motto.

     

    Malcolm

    Link to comment
    Share on other sites
    Old Joe
      On 1/7/2016 at 3:43 AM, Sparkey said:

    I like having an air compressor with spray nozzle to blow all of the dust off my work when its finished.

    I always spray a clear coat over fretwork before I frame it to keep any stray sawdust off the inside of the plexiglass.

    I keep a very small, cheap, shop vac next to my saw and use it constantly. I have also installed a ceiling mounted dust collector. Just blowing off the dust with the compressor is spreading it around the shop and it will end up in your finely sanded, oiled finish, not to mention your nose and lungs.

    Link to comment
    Share on other sites
    Jim Finn

           Two tips:

         To use more of your blade teeth you can cut off the bottom 3/4" of a dulled blade reinstall, and you will then be using the unused teeth.  Not sure all saws will accommodate the shorter blade but all mine will.

     

         I have an $8 hair dryer blowing the dust off of my work as I saw.

    Link to comment
    Share on other sites


    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.
    Note: Your post will require moderator approval before it will be visible.

    Guest
    Add a comment...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

    ×

  • Sponsored

    (Log In or Sign Up to remove this ad.)

×
×
  • Create New...