amazingkevin Posted February 20, 2016 Report Share Posted February 20, 2016 Did some electrical work on the 25" work bench today ,36 outlets in all on the bench One every 4" for a canope light ,one for a fan every 4' and one every 4 feet for a machine with and extra outlet. wombatie, tomsteve, Lucky2 and 1 other 4 Quote Link to comment Share on other sites More sharing options...
New Guy Posted February 20, 2016 Report Share Posted February 20, 2016 Great start - Please show us when done. amazingkevin 1 Quote Link to comment Share on other sites More sharing options...
kywoodmaster Posted February 21, 2016 Report Share Posted February 21, 2016 Good looking conduit job. Quote Link to comment Share on other sites More sharing options...
Scrolling Steve Posted February 21, 2016 Report Share Posted February 21, 2016 Keep up the good work Kevin! Quote Link to comment Share on other sites More sharing options...
Lucky2 Posted February 21, 2016 Report Share Posted February 21, 2016 Kevin, you're making great headway, just make sure you don't overload the breakers. Len Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 21, 2016 Author Report Share Posted February 21, 2016 Great start - Please show us when done. So much to do here ,I keep moving things to get to things and back again ugh! Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 21, 2016 Author Report Share Posted February 21, 2016 Good looking conduit job. Hope i don't get caught doing electical work ,no permit.But would you rather have me have lots of extention cords or the right way with out permits? Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 21, 2016 Author Report Share Posted February 21, 2016 Keep up the good work Kevin! Thanks Steve work will be pleasureable once i'm set up ,getting close! Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 21, 2016 Author Report Share Posted February 21, 2016 Kevin, you're making great headway, just make sure you don't overload the breakers. Len Np problem only one thing at a time is used that would draw some amps,Mostly just a fan a light and onev machine going intermittently.I did run #10 wire for the hot. Quote Link to comment Share on other sites More sharing options...
JimErn Posted February 22, 2016 Report Share Posted February 22, 2016 Hope i don't get caught doing electical work ,no permit.But would you rather have me have lots of extention cords or the right way with out permits? One way around that is run the conduit and boxes, and the end where you are going to apply the power, put a male end on the romex and plug it in to an existing outlet. Technically that makes it an extension cord. Find two outlets on different circuit breakers, and split the load. tomsteve 1 Quote Link to comment Share on other sites More sharing options...
WayneMahler Posted February 22, 2016 Report Share Posted February 22, 2016 Always to do it right the first time Kevin. Progress looks good so far. As for running #10 for a hot, that will be dictated by the size of the breaker in the panel. Keep us posted on your progress. tomsteve 1 Quote Link to comment Share on other sites More sharing options...
Denny Knappen Posted February 22, 2016 Report Share Posted February 22, 2016 Me and electricity don't get along. If I need wiring, I call my son. Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 22, 2016 Author Report Share Posted February 22, 2016 One way around that is run the conduit and boxes, and the end where you are going to apply the power, put a male end on the romex and plug it in to an existing outlet. Technically that makes it an extension cord. Find two outlets on different circuit breakers, and split the load. I had a though like that,I think your right! Your the best! Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 22, 2016 Author Report Share Posted February 22, 2016 Always to do it right the first time Kevin. Progress looks good so far. As for running #10 for a hot, that will be dictated by the size of the breaker in the panel. Keep us posted on your progress. #10 wire 30 amp yes!At no one time will i be drawing 5 amps.Thanks! WayneMahler 1 Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 22, 2016 Author Report Share Posted February 22, 2016 Me and electricity don't get along. If I need wiring, I call my son. I can't afford to,hire someone or pay for permits, so i'm forced to do everything myself,lol Quote Link to comment Share on other sites More sharing options...
CharleyL Posted February 22, 2016 Report Share Posted February 22, 2016 (edited) #10 gauge wire is not going to fit well under the screws on the outlets, and the outlets are not designed to be legally connected to a 30 amp circuit. You can only connect the standard 120 volt duplex outlets to 15 or 20 amp circuits legally. They aren't rated for 30 amps. If you have already bought and cut the #10 gauge wire, you can cut short pieces of #12 gauge wire to connect to the outlets and then splice these short #12 gauge pig tails to the #10 gauge wire with wire nuts. Then the most current that you can connect these circuits to is 20 amps and NOT 30 amps.You would be much better off using #12 gauge wire and splitting your outlets into several circuits of 15 or 20 amps each. If you have to plug these new outlet circuits into existing wall outlets because you can't connect them direct to circuit breakers in the panel, then use a length of type SJO rubber covered 3 conductor #12 gauge cable for the run between your last outlet box and the plug that you plug into the existing wall outlet. Where this wire goes into the end outlet box you need to use a rubber insert connector of the right size for the cable to protect the cable and provide strain relief. Yes, you have made a multi-outlet strip if making it this way, and it's legal, but it would be better if you could run the conduit to the breaker panel and connect the single strand of wiring direct to the circuit breaker, neutral, and ground in the panel. I'm an electrical engineer and have an electrician's license, but not in Florida. License or not, I know the right way to do this. Charley Edited February 22, 2016 by CharleyL NC Scroller, tomsteve and Sparkey 3 Quote Link to comment Share on other sites More sharing options...
Sparkey Posted February 23, 2016 Report Share Posted February 23, 2016 (edited) Yep what Charley said. I am a Licensed Master Electrician and that's how I would do it. Just to clear one thing up make sure to get the right outlet. There are 15 amp and 20 amp and you can't put 15 amp outlets on a 20 amp breaker. Edited February 23, 2016 by Sparkey tomsteve 1 Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 23, 2016 Author Report Share Posted February 23, 2016 #10 gauge wire is not going to fit well under the screws on the outlets, and the outlets are not designed to be legally connected to a 30 amp circuit. You can only connect the standard 120 volt duplex outlets to 15 or 20 amp circuits legally. They aren't rated for 30 amps. If you have already bought and cut the #10 gauge wire, you can cut short pieces of #12 gauge wire to connect to the outlets and then splice these short #12 gauge pig tails to the #10 gauge wire with wire nuts. Then the most current that you can connect these circuits to is 20 amps and NOT 30 amps.You would be much better off using #12 gauge wire and splitting your outlets into several circuits of 15 or 20 amps each. If you have to plug these new outlet circuits into existing wall outlets because you can't connect them direct to circuit breakers in the panel, then use a length of type SJO rubber covered 3 conductor #12 gauge cable for the run between your last outlet box and the plug that you plug into the existing wall outlet. Where this wire goes into the end outlet box you need to use a rubber insert connector of the right size for the cable to protect the cable and provide strain relief. Yes, you have made a multi-outlet strip if making it this way, and it's legal, but it would be better if you could run the conduit to the breaker panel and connect the single strand of wiring direct to the circuit breaker, neutral, and ground in the panel. I'm an electrical engineer and have an electrician's license, but not in Florida. License or not, I know the right way to do this. Charley Makes sense, i was skimping on details just to get power.i'lI get the !2 gauge and plug so i can make it an extension cord ,Thanks friend! tomsteve 1 Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 23, 2016 Author Report Share Posted February 23, 2016 Yep what Charley said. I am a Licensed Master Electrician and that's how I would do it. Just to clear one thing up make sure to get the right outlet. There are 15 amp and 20 amp and you can't put 15 amp outlets on a 20 amp breaker.The breaker box has three 20 amp circuit breakers and 15 amp outlets here? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.