125 CSL Posted September 28, 2016 Report Share Posted September 28, 2016 Cut my thumb on my scroll saw blade. For some time I have been wanting to start to cut out trivets. So for the past months I kept an eye out for people who were cutting down trees. Picked up a few chunks, let them cure/dry. Cut out a chunk and with my belt sander smoothed it out. I started cutting on my porter cable, but the #5 and 6 polar and spiral blades I have where just snapping no matter how slow the speed or how slow I pushed the work. So pulled out my old master craft scroll saw and pinned blades. I should have clamped it down, but did not. It vibrates, I was only paying attention to the where I was cutting. As the saw started to tip, reached up to steady the saw in doing so managed to get my thumb in the saw bade. Lesson, bolt down your saws, no matter how innocent it might look. I will have to find/make a folding table. Quote Link to comment Share on other sites More sharing options...
DWSUDEKUM Posted September 28, 2016 Report Share Posted September 28, 2016 This happens. Make yourself a stand there are several patterns wandering about for them. DW Quote Link to comment Share on other sites More sharing options...
hawkeye10 Posted September 28, 2016 Report Share Posted September 28, 2016 Sorry about that. I assume it wasn't to bad? Quote Link to comment Share on other sites More sharing options...
ike Posted September 28, 2016 Report Share Posted September 28, 2016 i HAD MY SAW BOLTED DOWN BEFORE i CU MY FIRS PIECE. i LEARNED A LONG TIME AGO THAT IF YOU A ARGUE WITH A POWER TOOL YOU ARE GOING TO LOST, i LOST 1/2 OF MY SUM WITH A TABLE SAW. . ike Lucky2 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted September 28, 2016 Report Share Posted September 28, 2016 OUCH! Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted September 29, 2016 Report Share Posted September 29, 2016 Cut my thumb on my scroll saw blade. For some time I have been wanting to start to cut out trivets. So for the past months I kept an eye out for people who were cutting down trees. Picked up a few chunks, let them cure/dry. Cut out a chunk and with my belt sander smoothed it out. I started cutting on my porter cable, but the #5 and 6 polar and spiral blades I have where just snapping no matter how slow the speed or how slow I pushed the work. So pulled out my old master craft scroll saw and pinned blades. I should have clamped it down, but did not. It vibrates, I was only paying attention to the where I was cutting. As the saw started to tip, reached up to steady the saw in doing so managed to get my thumb in the saw bade. Lesson, bolt down your saws, no matter how innocent it might look. I will have to find/make a folding table. Just be thankful it wasn't a piece of cut own nasty band saw blade,That would do more than bite,i know,got me once Quote Link to comment Share on other sites More sharing options...
WayneMahler Posted September 29, 2016 Report Share Posted September 29, 2016 Sorry to hear this. The closest I came wa a groove in a finger nail. Hope all is well and nothing too serious. Quote Link to comment Share on other sites More sharing options...
meflick Posted September 29, 2016 Report Share Posted September 29, 2016 Glad all is well. Glad "lesson" was learned. Hope others can learn from it as well perhaps. Quote Link to comment Share on other sites More sharing options...
Phantom Scroller Posted September 29, 2016 Report Share Posted September 29, 2016 Oh dear the what a pity never mind were the words you said am I correct. Roly bobscroll, Debi Shipman and Rob Roy 3 Quote Link to comment Share on other sites More sharing options...
Lucky2 Posted September 30, 2016 Report Share Posted September 30, 2016 Craig, thankfully it wasn't a severe cut, and hopefully you learned a lesson. Anything that vibrates as much as a scroll saw does, definitely should be fastened down before using. The probable reason for the blades snapping on you, was that the wood probably was still to wet to cut. The wood that you picked up in the last few months, wouldn't be near dry enough to use. It takes at least one year per inch, for fresh cut wood to air dry. Len Quote Link to comment Share on other sites More sharing options...
125 CSL Posted September 30, 2016 Author Report Share Posted September 30, 2016 Sorry about that. I assume it wasn't to bad? A bit over 1/2 inch across my thumb print. Made it bleed a bit longer then it would have naturally, Then washed it and applied abx band aids. Even after 30 years as a nurse it some times amazes me how quick the body recovers. Craig, thankfully it wasn't a severe cut, and hopefully you learned a lesson. Anything that vibrates as much as a scroll saw does, definitely should be fastened down before using. The probable reason for the blades snapping on you, was that the wood probably was still to wet to cut. The wood that you picked up in the last few months, wouldn't be near dry enough to use. It takes at least one year per inch, for fresh cut wood to air dry. Len Oh yea lesson learned. Figured it was red oak that was why the stuff would not cut on my PC, I will keep in mind the slow dry time. New to a lot of this. Oh dear the what a pity never mind were the words you said am I correct. Roly I have no idea what you are trying to say. Phantom Scroller 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.