Popular Post Old Joe Posted February 9, 2018 Popular Post Report Share Posted February 9, 2018 This is from a recent Steve Good pattern. It is made from one board, with the figure's outer perimeter cut with the table set at about a 3 1/2 degree.That allows the wood spirit to protrude a little over half way through from the back. I like the idea, but if I were to make another one I would redesign the mouth/mustache area, as I think it looks too big. On this project I used stains,rather than my normal oils, to try to make the backboard look like barn wood and the have the wood spirit contrast by being lighter. I have very recently built out a new shop and I'm just getting started making sawdust again. I hope to be a bit more active on this site. Phantom Scroller, jollyred, bobscroll and 10 others 13 Quote Link to comment Share on other sites More sharing options...
meflick Posted February 9, 2018 Report Share Posted February 9, 2018 Very nice Joe. It's nice to see that one made after seeing it on Steve's site. thanks for sharing. Quote Link to comment Share on other sites More sharing options...
scrollerpete Posted February 9, 2018 Report Share Posted February 9, 2018 Very nice project, excellent work Quote Link to comment Share on other sites More sharing options...
DWSUDEKUM Posted February 9, 2018 Report Share Posted February 9, 2018 Nicely done Pete. Thanks for sharing this with us. DW Quote Link to comment Share on other sites More sharing options...
Scrolling Steve Posted February 9, 2018 Report Share Posted February 9, 2018 That turned out great, Pete ! Quote Link to comment Share on other sites More sharing options...
Scrappile Posted February 9, 2018 Report Share Posted February 9, 2018 Great looking wood spirit! Quote Link to comment Share on other sites More sharing options...
heppnerguy Posted February 9, 2018 Report Share Posted February 9, 2018 I was hoping someone would cut this piece. I saw it on Steve's page and thought it might be a fun one to mess with. It sure turned out nice. Like the staining on the backer board. A perfect Idea for it Dick heppnerguy Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 10, 2018 Report Share Posted February 10, 2018 14 hours ago, Old Joe said: This is from a recent Steve Good pattern. It is made from one board, with the figure's outer perimeter cut with the table set at about a 3 1/2 degree.That allows the wood spirit to protrude a little over half way through from the back. I like the idea, but if I were to make another one I would redesign the mouth/mustache area, as I think it looks too big. On this project I used stains,rather than my normal oils, to try to make the backboard look like barn wood and the have the wood spirit contrast by being lighter. I have very recently built out a new shop and I'm just getting started making sawdust again. I hope to be a bit more active on this site. All of us would love to see the new shop!!! Nice cutting here!!!!!! Quote Link to comment Share on other sites More sharing options...
wombatie Posted February 10, 2018 Report Share Posted February 10, 2018 Excellent work Joe. I love it. Marg Quote Link to comment Share on other sites More sharing options...
Dan Posted February 10, 2018 Report Share Posted February 10, 2018 Great job! That's on my list. Quote Link to comment Share on other sites More sharing options...
daveww1 Posted February 10, 2018 Report Share Posted February 10, 2018 very nice Quote Link to comment Share on other sites More sharing options...
Old Joe Posted February 10, 2018 Author Report Share Posted February 10, 2018 4 hours ago, Dan said: Great job! That's on my list. Like I said, I would recommend you change the mouth area. Quote Link to comment Share on other sites More sharing options...
Phantom Scroller Posted February 10, 2018 Report Share Posted February 10, 2018 You did that one proud good job. Roly Quote Link to comment Share on other sites More sharing options...
rdatelle Posted February 10, 2018 Report Share Posted February 10, 2018 I like it' Love the wood you used. Your right about the mustache. I think a little smaller would look better but it looks good that way to. Quote Link to comment Share on other sites More sharing options...
Dan Posted February 10, 2018 Report Share Posted February 10, 2018 7 hours ago, Old Joe said: Like I said, I would recommend you change the mouth area. I was thinking the same thing when I saw Steve Goods piece. Quote Link to comment Share on other sites More sharing options...
GPscroller Posted February 11, 2018 Report Share Posted February 11, 2018 Great results. Jeff Quote Link to comment Share on other sites More sharing options...
Dave Monk Posted February 11, 2018 Report Share Posted February 11, 2018 Love the look you gave the wood. Quote Link to comment Share on other sites More sharing options...
Gordster Posted February 11, 2018 Report Share Posted February 11, 2018 You did a fine job on it. Quote Link to comment Share on other sites More sharing options...
Lucky2 Posted February 11, 2018 Report Share Posted February 11, 2018 Joe, that is just to freakin cool. Len Quote Link to comment Share on other sites More sharing options...
bobscroll Posted February 11, 2018 Report Share Posted February 11, 2018 Super job you did there Joe! It look great! Bob Quote Link to comment Share on other sites More sharing options...
Old Joe Posted February 12, 2018 Author Report Share Posted February 12, 2018 On 2/10/2018 at 3:24 PM, rdatelle said: I like it' Love the wood you used. Your right about the mustache. I think a little smaller would look better but it looks good that way to. Ralph, a cabinetmaker friend had a couple of actual 1 inch cedar boards in his trash pile. I am a shameless scavenger. Quote Link to comment Share on other sites More sharing options...
newfie Posted February 12, 2018 Report Share Posted February 12, 2018 Looks great thanks for sharing Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.