Lastchance Posted October 10, 2010 Report Share Posted October 10, 2010 What type of scroll blade is your work horse. The blade you use for most or general cutting. Do you use one blade for the outlines / big area cuts and then change blades when you move inside to finer cuts? Where do you purchase your blades from? Is there a chart somewhere that describes what scrollsaw blades are best for what type of work or lumber? What about lubes or oils for cutting? Do you use them and what types do you perfer? Thanks in advance for any information you can share. Trying to work smarter not harder. Chance Quote Link to comment Share on other sites More sharing options...
Kepy Posted October 10, 2010 Report Share Posted October 10, 2010 Click on the link to Mikesworkshop for Flying Dutchman blades. Mike will send you a sample pack. Every scroller has their own favorite. Mine happens to be a #5 Reverse. Quote Link to comment Share on other sites More sharing options...
FD Mike Posted October 10, 2010 Report Share Posted October 10, 2010 What type of scroll blade is your work horse. The blade you use for most or general cutting. It all depends what wood you use, how intricate the pattern is. Do you use one blade for the outlines / big area cuts and then change blades when you move inside to finer cuts? Most don't. You cut first all the inside cuts and than the out side with same blade because there might be a lot of intricate cuttings also. Where do you purchase your blades from? I don't think I have to say anymore. Is there a chart somewhere that describes what scrollsaw blades are best for what type of work or lumber? On my web site I have "Selecting a Blade". What about lubes or oils for cutting? Do you use them and what types do you perfer? Never, ever use oil to lubricaten the blade. It gets on the wood and you have to throw the pice away. Most use a blue painters tape on the wood, this helps to eliminate burning. The tape has a chemical on top what relecton releases friction. Some say it lubricate bvut that is not true. This I learned from the 3M tape division. I hope this is of some help Chance. FD Mike Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted October 10, 2010 Report Share Posted October 10, 2010 Hello Chance,If you try the spiral blades get the ones from mike and the ones with flat ends and make them guitar string tight,(high E)Blades with reverse teeth leave a clean cut edge top and bottom,other blades leave a clean edge only on the top.Saves alot of sanding if you need it sanded. Quote Link to comment Share on other sites More sharing options...
MBridges Posted October 10, 2010 Report Share Posted October 10, 2010 Mine is def. the Olsen #3 Mach Series. Quote Link to comment Share on other sites More sharing options...
Clayton717 Posted October 10, 2010 Report Share Posted October 10, 2010 my favorite is FD #5r or #7r. I use these two blades for almost everything I cut. Quote Link to comment Share on other sites More sharing options...
Huntter2022 Posted October 10, 2010 Report Share Posted October 10, 2010 Blade most used FD #5 ultra reverse , But do have a varity of blades, Puzzle , jewelers , sprials ,and ultra reverses also have a few blades I don't even know what they are samples from woodshows Quote Link to comment Share on other sites More sharing options...
medic_149 Posted October 11, 2010 Report Share Posted October 11, 2010 My favorite would be a 2/0 spiral. I use almost exclusivly spirals for eveything i cut. But i mostly cut portrait style projects. Each person will have there own cutting style and blage preference. the best advice on blades i could give someone is to get a variety pack and try them all out. This way you get first hand experience with how each blade responds to your cutting style. with this you will be able to decide which blades give you the best cut, detailing and so forth. Also, keep in mind wood plays a big part in how a blade cuts. Quote Link to comment Share on other sites More sharing options...
Oges Posted October 11, 2010 Report Share Posted October 11, 2010 I mostly use #3 and #5 reverse tooth blades for the work I do. I have some smaller ones that I use occasionally for other work as needed. I have a supplier here in Australia that I get my blades from, they sell the Flying Dutchman and also Pegas blades. Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted October 11, 2010 Report Share Posted October 11, 2010 For quick rips i love"FD-HD" from "mike@mikesworkshop.com" Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.