John B Posted August 30, 2018 Report Share Posted August 30, 2018 (edited) G'day all, I noticed in the Q & A Forum there was a bit of discussion regarding pin chucks and holding 1/16th or smaller bits in your drill press. This is my method, A mate actually got me the chuck, however I have collected a few chucks (I always remove the chuck before chucking a US drill ) since and given them to blokes I know. Most 1/4" chucks will grip the small bits. I found a bolt that fitted in the threaded end of the chuck, cut the head of it and that is now the shank that goes into the drill press. A picture is worth a thousand words Cheers John Edited August 30, 2018 by John B spelling OCtoolguy, kmmcrafts, WayneMahler and 3 others 5 1 Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted August 30, 2018 Report Share Posted August 30, 2018 Great idea.. I ended up buying a small bit chuck from Mikes when I started using the small bits.. My press would hold the 1/16 great.. but when I started using the real small numbered bits it wouldn't.. Where can one get a metric chuck for those metric drill bits.. I have a whole set of metric bits brand new.. but my chuck is standard US John B, jollyred, Scrappile and 1 other 4 Quote Link to comment Share on other sites More sharing options...
Roberta Moreton Posted August 30, 2018 Report Share Posted August 30, 2018 I use the dremel drill press. My Scroll Saw is that n the house. I am not,running outside to the big drill press to drill a few holes. John B and OCtoolguy 2 Quote Link to comment Share on other sites More sharing options...
loftyhermes Posted August 30, 2018 Report Share Posted August 30, 2018 I use a chuck like John but mine came out of an egg beater hand drill and had a plain shaft so I just put that in the drill press chuck. OCtoolguy and John B 1 1 Quote Link to comment Share on other sites More sharing options...
Scrappile Posted August 30, 2018 Report Share Posted August 30, 2018 The pin chuck I purchased just wasn't that good, had some wobble. I chucked that chuck..... in the garbage. I think John's idea would work great. My Jet drill press is a big one like 17" and the chuck closes all the way. The smaller drill press I use to use didn't. OCtoolguy and John B 1 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted August 30, 2018 Report Share Posted August 30, 2018 9 hours ago, kmmcrafts said: <SNIP> Where can one get a metric chuck for those metric drill bits.. I have a whole set of metric bits brand new.. but my chuck is standard US Same place one gets a metric Crescent wrench. WayneMahler, tgiro, kmmcrafts and 1 other 1 3 Quote Link to comment Share on other sites More sharing options...
Lucky2 Posted August 31, 2018 Report Share Posted August 31, 2018 I'm lucky I guess, my drill press will hold the small little ting bits. I do own a couple of small chucks for the Dremel tools, but I've never had to use them for scroll work. The drill press I use is made by Sears, it is a large bench top model. Len John B 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted September 1, 2018 Report Share Posted September 1, 2018 I hold bits down to #80 in a Dremel chuck mounted in a drill press. The Dremel chuck is about the most accurate chuck one can buy unless of course one can afford the Albrecht micro chuck on ebay for the measly price of only $179 plus $49 shipping. Get it now! Only 4 left. I hope the $49 shipping is a typo. John B 1 Quote Link to comment Share on other sites More sharing options...
Jim McDonald Posted September 1, 2018 Report Share Posted September 1, 2018 I use a Dremel and if the piece allows, I will use the Dremel drill press attachment. If not, I use the Dremel with a speed square to help guide me. John B 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted September 1, 2018 Report Share Posted September 1, 2018 Hi Jim. What is a speed square? Quote Link to comment Share on other sites More sharing options...
Bill WIlson Posted September 1, 2018 Report Share Posted September 1, 2018 Quote Link to comment Share on other sites More sharing options...
Jim McDonald Posted September 2, 2018 Report Share Posted September 2, 2018 Thanks Bill for the assist. Quote Link to comment Share on other sites More sharing options...
Rockytime Posted September 2, 2018 Report Share Posted September 2, 2018 1 hour ago, Bill WIlson said: Oh, thanks.I have several of those. I have always called them a Try Square. Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.