orangeman Posted October 27, 2018 Report Share Posted October 27, 2018 For those who use the Duck brand shelf paper here is some advice: Don't wait to remove it from the wood! I left some on the wood for over a month and it was very difficult to remove. It even lifted up some wood fibers! From now on I will always cut and remove the same day! bb OCtoolguy and SCROLLSAW703 1 1 Quote Link to comment Share on other sites More sharing options...
jollyred Posted October 27, 2018 Report Share Posted October 27, 2018 I have had that problem with all of the adhesives I have used to attach the patterns. The shelf paper seems to remove easier after some time than the others I have used. I just removed some that had been on the wood for almost a month, and didn't have too much problem with it. However, I usually do try to get it off in a day or two at the most. amazingkevin, OCtoolguy and SCROLLSAW703 3 Quote Link to comment Share on other sites More sharing options...
JTTHECLOCKMAN Posted October 27, 2018 Report Share Posted October 27, 2018 Will happen with painters tape too. I think I mentioned this one other thread some time ago. Also sometimes I find myself stacking weights on a piece to keep from warping before cutting and this adds to the problem. SCROLLSAW703, OCtoolguy and amazingkevin 2 1 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted October 27, 2018 Report Share Posted October 27, 2018 6 hours ago, orangeman said: For those who use the Duck brand shelf paper here is some advice: Don't wait to remove it from the wood! I left some on the wood for over a month and it was very difficult to remove. It even lifted up some wood fibers! From now on I will always cut and remove the same day! bb I left some on for a couple of months. Maybe longer. I just heated with a heat gun and it came right off. stoney, amazingkevin, Old Joe and 3 others 3 3 Quote Link to comment Share on other sites More sharing options...
stoney Posted October 27, 2018 Report Share Posted October 27, 2018 3 hours ago, octoolguy said: I left some on for a couple of months. Maybe longer. I just heated with a heat gun and it came right off. Heat gun does wonders for loosening adhesives. I use one quite often to remove labels. SCROLLSAW703, RabidAlien, OCtoolguy and 1 other 3 1 Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted October 27, 2018 Report Share Posted October 27, 2018 Yep... heat gun user here as well... but that said.. I've found also that they peel off harder in different temps.. If you don't have a heat gun... just set it out in the sun for 20 minutes or so.. that will also help some.. or the wife's hair dryer... RabidAlien, OCtoolguy, SCROLLSAW703 and 1 other 2 1 1 Quote Link to comment Share on other sites More sharing options...
JackM Posted October 27, 2018 Report Share Posted October 27, 2018 When doing fretwork, I sand it to 220 then spray a coat or two of shellac. Then apply painters tape, spray the pattern and apply it. Have removed patterns after a few months with no problems of fibers lifting. Jack amazingkevin, OCtoolguy and SCROLLSAW703 1 2 Quote Link to comment Share on other sites More sharing options...
JTTHECLOCKMAN Posted October 27, 2018 Report Share Posted October 27, 2018 3 hours ago, JackM said: When doing fretwork, I sand it to 220 then spray a coat or two of shellac. Then apply painters tape, spray the pattern and apply it. Have removed patterns after a few months with no problems of fibers lifting. Jack That would not work for me. I dip most my projects in Danish oil and the sealing of the wood with shellac would prevent that. But if it works for you then good to go. Many ways of getting the job done. Thanks for sharing. SCROLLSAW703 and OCtoolguy 2 Quote Link to comment Share on other sites More sharing options...
NLAlston Posted November 23, 2018 Report Share Posted November 23, 2018 On 10/26/2018 at 8:08 PM, orangeman said: For those who use the Duck brand shelf paper here is some advice: Don't wait to remove it from the wood! I left some on the wood for over a month and it was very difficult to remove. It even lifted up some wood fibers! From now on I will always cut and remove the same day! bb I have ALWAYS removed my adhesive papers/tapes from my projects immediately after completing the cuts. SCROLLSAW703, OCtoolguy and amazingkevin 3 Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted November 23, 2018 Report Share Posted November 23, 2018 More tips and tricks I didn't know about! And I have 2 heat guns. SCROLLSAW703 and OCtoolguy 2 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted November 25, 2018 Report Share Posted November 25, 2018 Funny, but I had several scraps covered with Duck brand for several months. It peeled off just fine. SCROLLSAW703 1 Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted November 25, 2018 Report Share Posted November 25, 2018 I've notice that temperature and humidity swings plays a role in how easy the stuff comes off.. I've had projects that the shelf liner was on for several months..peeled right off.. same shelf liner roll on another project around the same time frame just cooler temps came off harder than heck.. had to use the heat gun on it as the sun wasn't out and was rainy.. these couple of projects I applied the liner to the same day same roll.. and both had sat dang near a year.. I just did the cutting a couple weeks ago.. on both.. I don't know what it could be if it wasn't something with the rain or temps..or both.. because they both was applied to BB ply too.. nothing was different other than the temp / rain.. when I went to peel it off Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.