Rockytime Posted July 24, 2019 Author Report Share Posted July 24, 2019 Ray, you have to stop giving me ideas! You just caused me to spend $74.90 on the quick release. STOP IT! Now I have $100 for the saw, $74.90 for the tension release, $3.17 for a knob plus the cost of the 8' bolt. In addition gas to get the saw and then I bought lunch for my friend and I which was over $25. Lord, where will it ever end? The good news is I'll end up with a great little saw. Just have to work out dust collection. Hegner has one for my saw but I can work something out. OCtoolguy, Dave Monk and jbrowning 1 2 Quote Link to comment Share on other sites More sharing options...
jbrowning Posted July 24, 2019 Report Share Posted July 24, 2019 I did a dust collection on my Hegner 18" using PVC piping any my shop vac. Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 24, 2019 Author Report Share Posted July 24, 2019 3 minutes ago, jbrowning said: I did a dust collection on my Hegner 18" using PVC piping any my shop vac. Do you have photos? I can use suggestions. jbrowning 1 Quote Link to comment Share on other sites More sharing options...
jbrowning Posted July 24, 2019 Report Share Posted July 24, 2019 (edited) Here you go. This is the video I got my design from Rockytime. https://www.youtube.com/watch?v=SFM_jylYziY&t=17s Jim Edited July 24, 2019 by jbrowning OCtoolguy 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 24, 2019 Author Report Share Posted July 24, 2019 Thank you. It looks good. I'kk watch it. Also the long bolt to tighten the tilt, I took it off and replaced it with a metric hex bolt. I will perhaps never tilt the bed. If I do I have lots of wrenches. Also, the little thing that flips over the lower clamp, I removed it also. This little saw will work great. Thanks for the photo too. jbrowning and OCtoolguy 2 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted July 24, 2019 Report Share Posted July 24, 2019 19 hours ago, Rockytime said: Ray, you have to stop giving me ideas! You just caused me to spend $74.90 on the quick release. STOP IT! Now I have $100 for the saw, $74.90 for the tension release, $3.17 for a knob plus the cost of the 8' bolt. In addition gas to get the saw and then I bought lunch for my friend and I which was over $25. Lord, where will it ever end? The good news is I'll end up with a great little saw. Just have to work out dust collection. Hegner has one for my saw but I can work something out. Well, you were probably going to spend the lunch money anyway so all I'm responsible for is the tension lever assy. And you know you need it. I take it you got blade clamps and a clamp wrench with the saw? jbrowning 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 24, 2019 Author Report Share Posted July 24, 2019 7 minutes ago, octoolguy said: Well, you were probably going to spend the lunch money anyway so all I'm responsible for is the tension lever assy. And you know you need it. I take it you got blade clamps and a clamp wrench with the saw? Yes I got the clamps. The wrench is just a clock winding key OCtoolguy and jbrowning 2 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted July 24, 2019 Report Share Posted July 24, 2019 Just now, Rockytime said: Yes I got the clamps. The wrench is just a clock winding key You would know that. I had to spend $20 on one. Oh well, I got it all back when I sold it. I'm keeping an eye on the one that is here locally. It has a stand and is also variable speed but I just can't justify $200 for something that I don't need. I just want it. Maybe next week if it is still available. jbrowning 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 25, 2019 Author Report Share Posted July 25, 2019 Got the dust collection completed today. Complicated system. 4 1/2" rare earth magnets. jbrowning and OCtoolguy 1 1 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted July 25, 2019 Report Share Posted July 25, 2019 4 hours ago, Rockytime said: Got the dust collection completed today. Complicated system. 4 1/2" rare earth magnets. Simple is always best. jbrowning 1 Quote Link to comment Share on other sites More sharing options...
stoney Posted July 25, 2019 Report Share Posted July 25, 2019 (edited) Les you can make a similar to the Hegner upgrade tension release. I made one for an old 16" Craftsman. Just go to ebay and do a search for a cam lever. They are available with different threads to screw onto your rod. Edited July 25, 2019 by stoney OCtoolguy, jbrowning and Rockytime 1 2 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 26, 2019 Author Report Share Posted July 26, 2019 3 hours ago, stoney said: Les you can make a similar to the Hegner upgrade tension release. I made one for an old 16" Craftsman. Just go to ebay and do a search for a cam lever. They are available with different threads to screw onto your rod. Thanks Stoney. Unfortunately the Hegner one for $74 will arrive tomorrow. Not sure why but I sometimes do things on impulse. Never thought of the obvious but thanks anyway. OCtoolguy, stoney and jbrowning 3 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted July 26, 2019 Report Share Posted July 26, 2019 10 minutes ago, Rockytime said: Thanks Stoney. Unfortunately the Hegner one for $74 will arrive tomorrow. Not sure why but I sometimes do things on impulse. Never thought of the obvious but thanks anyway. It's rapidly becoming a $200 saw. Still not bad. I can still get the one nearby me for $200 but it has no stand. You got a great deal. jbrowning and Rockytime 2 Quote Link to comment Share on other sites More sharing options...
stoney Posted July 26, 2019 Report Share Posted July 26, 2019 11 hours ago, Rockytime said: Thanks Stoney. Unfortunately the Hegner one for $74 will arrive tomorrow. Not sure why but I sometimes do things on impulse. Never thought of the obvious but thanks anyway. You are welcome and not alone Les, most of us buy on impulse sometimes but like Ray said you got a great deal on the saw. I just thought maybe I could catch you in time and save you a little cash. OCtoolguy, Rockytime and jbrowning 2 1 Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted July 26, 2019 Report Share Posted July 26, 2019 56 minutes ago, stoney said: You are welcome and not alone Les, most of us buy on impulse sometimes but like Ray said you got a great deal on the saw. I just thought maybe I could catch you in time and save you a little cash. Thanks for bringing that up.. I'm kinda looking out for a Hegner.. Not been too many around lately... now that I have some cash.. but boy there was some deals a month or two ago when I was broke, LOL.. Real nice 22" newer one a while back for $250.. and not far from me.. I had a hard time passing on it.. but didn't want to stretch the cash too thin.. Should have bought it and then sold the older Hawk I have.. as Les said earlier "Sometimes one has to ignore good sense." stoney, OCtoolguy and jbrowning 3 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 27, 2019 Author Report Share Posted July 27, 2019 Put the quick release on and it works well. But...as Stoney said this can be made with a bolt, spring, washer and $6 cam lever. Gonna cut some word art from !" pine and run it through some paces. stoney, OCtoolguy, jbrowning and 1 other 3 1 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted July 27, 2019 Report Share Posted July 27, 2019 Actually Les, it sounds like you are having the same problems moving from your Hawk to your Hegner as I am having switching from my EX to my Hawk. I think I finally have the Hawk figured out. I kept thinking all my blades were too short until I watched the video a couple of times. Then the light came on. But, having the quick clamp will make it a lot easier. Now, if they would just make the quick release for the little one. I'll bet a good machinist could come up with one. Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 28, 2019 Author Report Share Posted July 28, 2019 1 hour ago, octoolguy said: Actually Les, it sounds like you are having the same problems moving from your Hawk to your Hegner as I am having switching from my EX to my Hawk. I think I finally have the Hawk figured out. I kept thinking all my blades were too short until I watched the video a couple of times. Then the light came on. But, having the quick clamp will make it a lot easier. Now, if they would just make the quick release for the little one. I'll bet a good machinist could come up with one. If the new clamp works as Hegner claims I should not need the quick release besides where can I find a machinist? OCtoolguy 1 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted July 28, 2019 Report Share Posted July 28, 2019 1 hour ago, Rockytime said: If the new clamp works as Hegner claims I should not need the quick release besides where can I find a machinist? Somewhere in Denver? Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 29, 2019 Author Report Share Posted July 29, 2019 I ordered the quick clamp from Hegner Saturday evening which means I have to wait until Wednesday or Thursday. Last night I just made a temporary clamp. It works perfect and was too late to cancel the order. So today I gave the saw it's first taste of cutting. stoney and OCtoolguy 1 1 Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted July 29, 2019 Report Share Posted July 29, 2019 49 minutes ago, Rockytime said: I ordered the quick clamp from Hegner Saturday evening which means I have to wait until Wednesday or Thursday. Last night I just made a temporary clamp. It works perfect and was too late to cancel the order. So today I gave the saw it's first taste of cutting. You must have found a machinist to help you make that.. OCtoolguy 1 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted July 29, 2019 Report Share Posted July 29, 2019 31 minutes ago, kmmcrafts said: You must have found a machinist to help you make that.. Very good Les. Maybe you can come up with some other add-ons for your saw and get rich. stoney 1 Quote Link to comment Share on other sites More sharing options...
Rockytime Posted July 30, 2019 Author Report Share Posted July 30, 2019 Working on it! :>) stoney and OCtoolguy 2 Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.