new2woodwrk Posted January 9, 2020 Report Share Posted January 9, 2020 I just got a new Guinever sander and am looking for suggestions/examples of how others have set up their dust and piece control. I'm thinking some kind of shroud around the 2 drum heads with screened dust ctrl hole in the back? Would love to see what others have done - pics are most welcome Thoughts? Thanks as always in advance OCtoolguy 1 Quote Link to comment Share on other sites More sharing options...
OCtoolguy Posted January 10, 2020 Report Share Posted January 10, 2020 2 hours ago, new2woodwrk said: I just got a new Guinever sander and am looking for suggestions/examples of how others have set up their dust and piece control. I'm thinking some kind of shroud around the 2 drum heads with screened dust ctrl hole in the back? Would love to see what others have done - pics are most welcome Thoughts? Thanks as always in advance I will be following this thread. I have looked at that same sander. Pics please. new2woodwrk 1 Quote Link to comment Share on other sites More sharing options...
Roberta Moreton Posted January 10, 2020 Report Share Posted January 10, 2020 I bought the flex sander shroud that fixes to my dust collection. I don’t really use the other one. Remember, I am in the house. OCtoolguy and new2woodwrk 2 Quote Link to comment Share on other sites More sharing options...
Rolf Posted January 10, 2020 Report Share Posted January 10, 2020 This is what I have done. On my pneumatic drums and sanding mop. notice the minimal gap on top and open on the bottom. NC Scroller, Whisper, Sycamore67 and 2 others 4 1 Quote Link to comment Share on other sites More sharing options...
Sycamore67 Posted January 10, 2020 Report Share Posted January 10, 2020 (edited) I have built something very similar to Rolf for My pneumatic drum sanders. It works well but I have a strong dust collector and am pulling around 650-700 cfm thru it. For somethings like sanding on the lathe or drill press, I have tried using a bell mouth hood on the end of the dust collection hose. It seems to work much more effectively than just the end of a hose. I read about it on the Australian forum woodworkforums.com Edited January 10, 2020 by Sycamore67 new2woodwrk, Rolf, OCtoolguy and 1 other 3 1 Quote Link to comment Share on other sites More sharing options...
Rolf Posted January 11, 2020 Report Share Posted January 11, 2020 I have my system connected to A JET Vortex 1100 VX. It is a Cyclone wanabe, that is surprisingly effective, with a 2 micron cartridge filter that is the original. I bought it in Dec 2011. It has had a lot of chips and dust go through it. especially fine dust when doing Intarsia. 4"pvc pipe, longest run ~30 ft. and 4 elbows and a 2" reducer to my bench top router at the end of the run, still lots of suction. GrampaJim, OCtoolguy and new2woodwrk 2 1 Quote Link to comment Share on other sites More sharing options...
Puzzleguy Posted January 11, 2020 Report Share Posted January 11, 2020 (edited) I basically cover my suction unit with an old woven onion bag ( from an old bag of onions ) which catches any loose parts from going up the line to the collector. loose one part of a large design and it pretty much ruins your day -makes the whole thing junk. 2 hours down the drain ( or worse ) The shrouds you guys have around your sanders are pretty neat - mine i just pull behind the unit Edited January 13, 2020 by Puzzleguy new2woodwrk, OCtoolguy and Rolf 3 Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.