kmmcrafts Posted February 12, 2020 Report Share Posted February 12, 2020 I made another video cutting out a puzzle on my Excalibur this morning. My phone picks up the led light waves (black lines) so I shut off the light a couple minutes into the video. I made a mistake on this puzzle, let’s see who points it out. My new phone is much bigger than my old one and makes it even harder to see my work as I tape my phone to the lens of the magnifying light so you see better than I do Enjoy Dennisfm56, amazingkevin, jollyred and 3 others 5 1 Quote Link to comment Share on other sites More sharing options...
scrollingforsanity Posted February 12, 2020 Report Share Posted February 12, 2020 Very nice Kevin. Guess I was to busy watching you work I missed the mistake. What blade were you using on that? Quote Link to comment Share on other sites More sharing options...
Rockytime Posted February 12, 2020 Report Share Posted February 12, 2020 Good video. Perhaps your mistake is not cutting a German Shepherd. Was your mistake not drilling for the dowel? kmmcrafts 1 Quote Link to comment Share on other sites More sharing options...
Cheryl Davis Posted February 12, 2020 Report Share Posted February 12, 2020 Wow Kevin, I hope at some point I can do something like that. Really awesome. Quote Link to comment Share on other sites More sharing options...
new2woodwrk Posted February 12, 2020 Report Share Posted February 12, 2020 Wow, awesome! I hope that video was sped up because that was an insane cut! Thanks for sharing it. Quote Link to comment Share on other sites More sharing options...
kmmcrafts Posted February 12, 2020 Author Report Share Posted February 12, 2020 (edited) 10 hours ago, scrollingforsanity said: Very nice Kevin. Guess I was to busy watching you work I missed the mistake. What blade were you using on that? 10 hours ago, Rockytime said: Good video. Perhaps your mistake is not cutting a German Shepherd. Was your mistake not drilling for the dowel? The mistake was I should have cut that little sliver off of the O after cutting out the R right around the -2:37 minutes left of the video mark.. Instead I cut out the O.. But at least I caught that before taking the pattern off and made the cut.. Blade was a #3 Pegas MG. Took me a few minutes longer than it should have because of the camera.. and the fact that I normally move the light out of my way during blade changes so the light was in my way for them.. and of coarse.. much harder to scroll looking through the phone screen instead of through my mag light.. with the light on I kept getting the LED wave link ( black spots and couldn't see what was going on.. then turning the light off made it hard to do as well.. But I got through the whole thing before iving up, LOL... I normally use my other mag light that is florescent bulb for doing videos.. but my son it borrowing it... OH Yes.. forgot to mention.. I did speed up the video.. ( I think 5x ) normal video was about 34 minutes ) I normally can cut this out in just under 20 minutes. but with video etc took a little extra time.. plus I bent a blade there near the beginning so I had to get another blade. not sure you caught that either.. Being the video was sped up it was easily missed.. Bent the blade because the mag light was in my way, LOL.. as I said... normally move it out of the way.. Just didn't want to bounce the video all around by moving the light.. as the camera was taped to my mag light lens.. so you see what I see while cutting.. Edited February 12, 2020 by kmmcrafts scrollingforsanity 1 Quote Link to comment Share on other sites More sharing options...
ike Posted February 12, 2020 Report Share Posted February 12, 2020 Nice video IKE Quote Link to comment Share on other sites More sharing options...
amazingkevin Posted February 12, 2020 Report Share Posted February 12, 2020 I too missed your mistake, good save!!! Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.