Popular Post Old Joe Posted October 12, 2021 Popular Post Report Share Posted October 12, 2021 I just finished this Mike Williams pattern. I like to cut portraits pretty small and I cut this one 9x6 inches. It made for some pretty intense scrolling, all done with Pegas 2/0 spiral blades on my Pegas saw. I hope you enjoy it. I haven’t posted on here in a while, though I scroll almost everyday. I was deeply saddened to see the news about the passing of Les. This community lost a very encouraging contributor. munzieb, jr42, JAC1961 and 19 others 21 1 Quote Link to comment Share on other sites More sharing options...
Scrappile Posted October 12, 2021 Report Share Posted October 12, 2021 (edited) That is a great pattern... You did a great job with it... Every day I keep expecting to see a post from Les... transmitted from up above... I also miss him a lot... Edited October 12, 2021 by Scrappile Old Joe 1 Quote Link to comment Share on other sites More sharing options...
Dak0ta52 Posted October 12, 2021 Report Share Posted October 12, 2021 I've seen that pattern and almost got it to cut myself. You did an excellent job. Still may fall on my "to do" list down the road. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
Foxfold Posted October 12, 2021 Report Share Posted October 12, 2021 Excellent job. I couldn't cut anything so small, envy you your talent. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
Old Joe Posted October 12, 2021 Author Report Share Posted October 12, 2021 10 minutes ago, Foxfold said: Excellent job. I couldn't cut anything so small, envy you your talent. Thanks, Brenda. I enjoy the challenge of cutting intricate patterns as small as I can without ending up with a muddled mess. It’s getting harder, mainly due to developing cataracts. Quote Link to comment Share on other sites More sharing options...
FrankEV Posted October 12, 2021 Report Share Posted October 12, 2021 Great job on a great pattern. Those 2/0 sprirals do wonders, but realy tough cutting when the drill hole is almost as big or bigger that the cutout...I know I've done many. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
Denny Knappen Posted October 12, 2021 Report Share Posted October 12, 2021 Very well done on a delicate project. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
Old Joe Posted October 12, 2021 Author Report Share Posted October 12, 2021 1 hour ago, FrankEV said: Great job on a great pattern. Those 2/0 sprirals do wonders, but realy tough cutting when the drill hole is almost as big or bigger that the cutout...I know I've done many. I have learned to get along with them to a point that I depend on them too much sometimes. I wish they made even smaller ones. I bought a kit of circuit board diameter bits and open the holes as needed from the back side. Of course I do occasionally bend a blade and then sometimes they break when I clamp them in too tight. FrankEV 1 Quote Link to comment Share on other sites More sharing options...
FrankEV Posted October 12, 2021 Report Share Posted October 12, 2021 2 minutes ago, Old Joe said: I have learned to get along with them to a point that I depend on them too much sometimes. I....I do occasionally bend a blade and then sometimes they break when I clamp them in too tight. Same here, totally my go to blade for most of what I do and also wish they made a smaller size. I break more blades because they get kinked when threading them through the drill holes. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
Scrappile Posted October 12, 2021 Report Share Posted October 12, 2021 31 minutes ago, FrankEV said: Same here, totally my go to blade for most of what I do and also wish they made a smaller size. I break more blades because they get kinked when threading them through the drill holes. Flying Dutchman "New Spiral" 3/0... FrankEV and Old Joe 2 Quote Link to comment Share on other sites More sharing options...
daveww1 Posted October 13, 2021 Report Share Posted October 13, 2021 amazing job Old Joe 1 Quote Link to comment Share on other sites More sharing options...
meflick Posted October 13, 2021 Report Share Posted October 13, 2021 Awesome work. Yes, I miss seeing Les and his posts and replies. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
scrollerpete Posted October 13, 2021 Report Share Posted October 13, 2021 Wow wow wow that is some fine cutting. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
bobscroll Posted October 13, 2021 Report Share Posted October 13, 2021 A beautiful piece of scrolling there Joe! That is something to be proud of, Thank you for posting, Bob Old Joe 1 Quote Link to comment Share on other sites More sharing options...
Charlie E Posted October 14, 2021 Report Share Posted October 14, 2021 Great job! The floorboards give it a real 3D look. Les would have loved this one. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
wombatie Posted October 14, 2021 Report Share Posted October 14, 2021 Oh wow that is small for something so intricate. That is certainly worth a 10+/10 Marg Old Joe 1 Quote Link to comment Share on other sites More sharing options...
rdatelle Posted October 14, 2021 Report Share Posted October 14, 2021 You did awesome on that piece. Still wish I could get used to spiral blades. Old Joe 1 Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.