Jump to content
🎄 🎄 🎄 2024 Custom Ornament Business Kit - Now Available - SALE 50% Off Through Dec. 2nd ×
Ornaments For Charity eBook - Designers Wanted! ​​​​​​​🙏 ×

Arrgh! I blinked again and lost another leaf


MarieC

Recommended Posts

It seems when I get really close to something that is delicate, I blink.  So it happened once again, and then I am down on my hands and knees in the sawdust looking for my leaf, which I luckily found.  So CA glue to the rescue, but it is so tiny I have to use a tweezer and when I pick it up it pops out of the tweezer and flys across the room!  I luckily find it again, but this time I didn't use a tweezer and the leaf gets stuck to my finger!  Arrgh!  Does this happen to anyone else or just me?  Does it get less frequent (blinking) as you get better?  Any tips?  I will hopefully show you my trees soon and hope that they won't be snags by the time I get them done!🤣  Thanks for your suggestions ahead of time...mariec

Edited by MarieC
Link to comment
Share on other sites

Blinking?  I never thought much about it.  Although, now that you have brought it to my attention, I'm sure it will find a place in my consciousness.  So thanks for that.  🤨 😛

As for dropping tiny bits on the floor, that happens all too often.  The only difference is that I rarely find what I dropped.  There must be some metaphysical connection with the clothes dryer and all of these lost bits & pieces have joined with the missing socks, in some Bermuda triangle like alternate existence.

 

Link to comment
Share on other sites

could be worse..I had a foreman who lost a crown on a front tooth and decided to CA it until he could get a dentist appointment. By the time he was done, he had successfully glued the crown back in but he had also glued his finger to it and the one next to it and they both came out in the end. 

Link to comment
Share on other sites

5 hours ago, BadBob said:

It happens to me and usually goes underneath something.

I used to lose small pieces while using my sanding mop. Two things helped that a lot. A tall fence on the back of the drill press stops 98% of them, and a net over the end of my dust collection to keep them from entering the shop vac. 

Awww, the net over the dust collection system....what a great idea...I have lost a many things to my dust collection system....Thanks for that tip!

Link to comment
Share on other sites

As I was reading your story I was thinking "her luck is almost as bad as mine." My brother could take dog droppings and make money from it whereas I would most likely trip and fall into it face first. The old saying, "If it wasn't for bad luck, I wouldn't have any luck at all," definitely applies to me. Does it get better? If it does for you, please let me know. It would give me something to look forward to.

Link to comment
Share on other sites

At my age, whenever a small item falls to the floor, I have a series of qualifying decisions to make. Do I really need it? Do I have more in the box? Can I see it on the floor? Is it easily accessible? Is it ferrous? If so, where did I use the magnet last? If I've answered all those questions satisfactorily and the magnet retrieval doo-hicky isn't found or not applicable, it's time to get down on the floor. Which brings about another set of questions. Is the object in such a spot that my huge girth can fit in order to grab the wayward, lost object.  Can I use a bench or tool to help me get up. Preferably, something not on wheels and not easily tippable. If all the conditions are right and I'm down on hands and knees or, more likely, on my butt, there one final question..."Now, Is there anything else I can do while I'm down here?"

Link to comment
Share on other sites

  • 1 month later...

On my Excalibur saws, the sawdust that doesn't get caught up by the dust control will filter down onto my lap or shoes. So, I made a couple of slide in/slide out boxes and they catch what dust makes it through. That's where all the tiny pieces also go if they don't get sucked up. So far I've had good luck with finding them. If they do get sucked up, well, that's called "creative license".

Link to comment
Share on other sites

1 hour ago, OCtoolguy said:

On my Excalibur saws, the sawdust that doesn't get caught up by the dust control will filter down onto my lap or shoes. So, I made a couple of slide in/slide out boxes and they catch what dust makes it through. That's where all the tiny pieces also go if they don't get sucked up. So far I've had good luck with finding them. If they do get sucked up, well, that's called "creative license".

Ray, if you get a minute, could you take a picture of your slide in/out boxes...are they on the floor or just under the saw table?  

Link to comment
Share on other sites

On 6/14/2023 at 1:45 PM, MarieC said:

Ray, if you get a minute, could you take a picture of your slide in/out boxes...are they on the floor or just under the saw table?  

Just under the frame of the saw so that all the dust just drops down into them. 3 Sided with a bottom. 1/8" BB ply.

 

20230616_151348.jpg

20230616_151358.jpg

Edited by OCtoolguy
Link to comment
Share on other sites

  • 3 weeks later...

I found that a cardboard box with an open side and a piece of foam taped to the back of the box can catch the pieces the mop insists of grabbing and trying to throw across the room when sanding the edges on the drill press.  When I get the saw and drill press set up again, I'll take a picture or two so you can see what I mean.

Link to comment
Share on other sites

12 hours ago, grandpuppies said:

I found that a cardboard box with an open side and a piece of foam taped to the back of the box can catch the pieces the mop insists of grabbing and trying to throw across the room when sanding the edges on the drill press.  When I get the saw and drill press set up again, I'll take a picture or two so you can see what I mean.

I use my mop on a large drill press. Having a tall fence on the back will also help with this. Before I had the fence the sanding mop would always throw the pieces behind or under something.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...