Jump to content
🎄 🎄 🎄 2024 Custom Ornament Business Kit - Now Available - SALE 50% Off Through Dec. 2nd ×

Bevel Setting Gauge


BadBob

Recommended Posts

I must be lame because I've been scrolling since around 2005 and only changed the angle of my saw maybe 2-3 times, and that was just to do an experiment.. I can say though with just my real limited angle cutting that If I were to do much angle cutting I'd have to have a Pegas or Ex saw that the head tilts instead of the table.. 

 

This tool looks like it'd be real handy to have, I always wanted to try making some bowls.. and now that I have about 500bft of walnut lumber I might  have to give it a try since fretwork style cuttings from dark walnut really doesn't look great and the fine cut lines are hard to see since the wood is so dark. I have a lot of spalted maple too that I need to use up.. sounds like I just talked myself into buying this tool and making some bowls.. Thanks 🤣 

Link to comment
Share on other sites

10 hours ago, kmmcrafts said:

sounds like I just talked myself into buying this tool and making some bowls.. Thanks

Just call me the great enabler. 😁

I am wanting to make bowls and baskets. From my understanding, the angles for these need to be precisely set. Using this tool would be much easier than getting down on the floor and turning the knob, then making a test cut to see how close you are.

I like the iGaging version better than the Taylor tools version primarily because the ruler on the other side is a center finding a rule.

Link to comment
Share on other sites

I have a clear plastic block with red filled angle lines that I use most frequently. Sorry, I don't remember where I bought it. I also have a bunch of yellow plastic pieces kind-of U shaped, but with a flat bottom, and each leg of each piece in the set is a different angle in 1 degree increments. Both were bought 20-25 years ago and I haven't seen either for sale in a very long time.

The Wixey angle gauge is a good modern way that I use for setting my table saw angle, and this will work fine if adjusting the table angle, if the table is at true 90 degrees to the blade to start with. Otherwise, there is no way to set zero degrees on the Wixey. You can get very close to blade 90 to the table if you take a square block of wood and cut a single width blade slot in one side. Then move this block around to the back side of the blade and see if the blade slides easily into the slot without the saw running. If it does, the table and blade are very close to 90 degrees with each other. You can then use the Wixey, setting it to zero while it's sitting on the table. Then tilt the table to the desired reading on the Wixey. You can get very close to the desired table angle this way, but it will not likely be perfect. The problem is all in how the Wixey zero setting is determined.

Charley

 

Edited by CharleyL
Link to comment
Share on other sites

23 hours ago, Rolf said:

I usually use my Wixey gauge when changing the angle. But many years ago I drew this in Autocad based on an article in SSWWC. Printed if out (red) and glued it to a piece of Plexiglass.sawangles-Model.thumb.jpg.a8cf9a5a06ae8bed06b7a91d14b25aa3.jpg

I saw one of these patterns in an old magazine which is what started all of this. When I saw the pattern, my brain said, "I think I have seen one of these somewhere else," and I started searching. I don't think I could make what I would consider accurate from a pattern.

Link to comment
Share on other sites

On 6/10/2023 at 10:58 PM, CharleyL said:

Otherwise, there is no way to set zero degrees on the Wixey…The problem is all in how the Wixey zero setting is determined.

Charley, couldn’t you use the magnets on the bottom of the Wiley to align on the blade to zero it?  Then if the table is @ 90 you know it’s perpendicular to the blade.

Link to comment
Share on other sites

On 6/10/2023 at 10:58 PM, CharleyL said:

 

The Wixey angle gauge is a good modern way that I use for setting my table saw angle, and this will work fine if adjusting the table angle, if the table is at true 90 degrees to the blade to start with. Otherwise, there is no way to set zero degrees on the Wixey. 

Charley

 

If you set your Wixey on the table and press the on/off button it will reset to Zero.  They have always done that. The newer version has another bubble level that is always calibrated to 0 degrees.

I have two saws a Hawk G4 that tilts the table and a EX-16 with tilting arm. On the EX I put the gauge on the arm.  

A tip Every once in awhile I come across one of the metal strip in the road that comes off of the street sweeper brushes, it fits perfectly in y clamps and allows me to put the wixey on it. It is wider and flatter than a blade. 

Wixey.jpg

Edited by Rolf
Link to comment
Share on other sites

On 6/13/2023 at 6:17 AM, Rolf said:

If you set your Wixey on the table and press the on/off button it will reset to Zero.  They have always done that. The newer version has another bubble level that is always calibrated to 0 degrees.

I have two saws a Hawk G4 that tilts the table and a EX-16 with tilting arm. On the EX I put the gauge on the arm.  

A tip Every once in awhile I come across one of the metal strip in the road that comes off of the street sweeper brushes, it fits perfectly in y clamps and allows me to put the wixey on it. It is wider and flatter than a blade. 

Wixey.jpg

Can you post a pic of what you are describing Rolf? I'd like to see how you have yours set up.

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...