Popular Post Dan Posted December 26, 2023 Popular Post Report Share Posted December 26, 2023 Well, it's probably been two years since I posted anything I made. This is a pattern from Scroll Saw Woodworking and Crafts, Fall 2008. Since day the day I received the magazine I said I was going to try this pattern. Let's see, that's 2023 minus 2008, subtract, carry the 1, about 15 years ago. Dick Miraglia was featured in that issue and did a fine job explaining the steps. I was a little hesitant about some of the steps but decided I could always use the firewood if it doesn't work out. Grabbed a maple slab, cut to size, used a trim router to lower the perimeter, then the fun started. The scrolling was straightforward but the maple made is slower than I'm use to. The trickiest part was carving/shaping the face. Not too bad, but I'd tackle it a bit different next time. The detailing was fast and fun. A big shout to @dickmira for the great article. I'll be doing some others as soon as I create some patterns. Cheer everyone! meflick, FrankEV, Wilson142 and 24 others 27 Quote Link to comment Share on other sites More sharing options...
Ron Johnson Posted December 26, 2023 Report Share Posted December 26, 2023 I recall this pattern and I probably still have the magazine. You did an amazing job Dan. danny and Dan 1 1 Quote Link to comment Share on other sites More sharing options...
Sycamore67 Posted December 27, 2023 Report Share Posted December 27, 2023 Dan...that is an excellent job ! I am very impressed with it ! Dan and danny 1 1 Quote Link to comment Share on other sites More sharing options...
JessL Posted December 27, 2023 Report Share Posted December 27, 2023 That looks great! Dan 1 Quote Link to comment Share on other sites More sharing options...
wombatie Posted December 28, 2023 Report Share Posted December 28, 2023 Everything starts with the first step and you have taken it and boy what a terrific outcome. You did an amazing job, well done. Marg Roberta Moreton and Dan 1 1 Quote Link to comment Share on other sites More sharing options...
Scrappile Posted December 28, 2023 Report Share Posted December 28, 2023 Gret job! Dan 1 Quote Link to comment Share on other sites More sharing options...
Denny Knappen Posted December 28, 2023 Report Share Posted December 28, 2023 My, that is impressive. What did you ue for the carving? Dan 1 Quote Link to comment Share on other sites More sharing options...
heppnerguy Posted December 28, 2023 Report Share Posted December 28, 2023 I gave it a try also but was not very happy with how it turned out. Was an interesting and different concept and just may give it another effort later on, who knows. Yours came out quite nice. Congratulations to you Dick heppnerguy Dan 1 Quote Link to comment Share on other sites More sharing options...
Dan Posted December 28, 2023 Author Report Share Posted December 28, 2023 (edited) 5 hours ago, Denny Knappen said: My, that is impressive. What did you ue for the carving? I used a Dremel and various bits. I considered trying some carving tools but don't have the patience right now. It's a little hard to tell from the photo but the sanding isn't the best. Again, patience. Edited December 28, 2023 by Dan Quote Link to comment Share on other sites More sharing options...
Peter N White Posted December 28, 2023 Report Share Posted December 28, 2023 Very well done. Dan 1 Quote Link to comment Share on other sites More sharing options...
DickMira Posted December 30, 2023 Report Share Posted December 30, 2023 To be honest, Dan, I was extremely busy with the holiday festivities and all of the visiting family staying with us that I did not have any opportunities to look at the recent forum postings. I was very pleasantly surprised this morning to see your post featuring the tremendous carving job you did on the tiger. I have seen many carved fretwork tigers from different woodworkers following the instructions in this article and have helped many with further instructions. However, your tiger is one of the best jobs and I loved it. Keep at it and it does get easier. Have a great new year to you and all my colleagues on Scrollsaw Village, Dick Mira Roberta Moreton, Dan, Scrappile and 1 other 3 1 Quote Link to comment Share on other sites More sharing options...
Rolf Posted December 31, 2023 Report Share Posted December 31, 2023 Dan great job, it is also on my long list of things I want to do. I had the pleasure of meeting Dick at one of Fox Chapels open houses and saw display with all of the different carved panels. Dan 1 Quote Link to comment Share on other sites More sharing options...
DickMira Posted January 4 Report Share Posted January 4 SAFETY TIP Since this article was originally published, I have learned that there are many folks who are very timid about using a hand held router to lower the background on projects like this. This task can be easily and safely accomplished by using a Typhoon type bit in the Dremel or other hand held rotary tool to lower the background. Dick Mira Quote Link to comment Share on other sites More sharing options...
Charlie E Posted January 5 Report Share Posted January 5 Nice job Dan! Dan 1 Quote Link to comment Share on other sites More sharing options...
.thumb.jpg.95d348aa76923344a5cab534cc1b3bc1.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.